Configure your radio hardware and user identity parameters.
User Settings
User Profile
Setting
Опис
Довга назва
Your display name (up to 39 characters)
Коротка назва
4-character abbreviated name
Licensed Operator
Enable if you hold an amateur radio license (enables higher power)
Applying Changes
After modifying settings, tap Save to write the configuration to your radio. The device may reboot to apply changes.
Radio Configuration
Налаштування пристрою
Setting
Опис
За замовчуванням
Роль
Node behavior (Client, Router, etc.)
Клієнт
Режим ретрансляції
How the node retransmits messages
Усі
Node Info Broadcast (s)
Interval for broadcasting node info
10800
Double-tap Button
Action for double-tap button press
Disabled
Налаштування LoRa
Setting
Опис
За замовчуванням
Регіон
Regulatory region for frequency bands
Unset (must configure)
Modem Preset
Speed/range tradeoff
LongFast
Hop Limit
Maximum retransmit hops
3
TX Power
Transmission power (dBm); 0 = max allowed for region
0 (region max)
Frequency Offset
Fine-tune frequency (MHz)
0
Channel Bandwidth
Bandwidth setting
Default for preset
⚠️ Important: You must set your region before transmitting. Operating without the correct region may violate local radio regulations. See the region configuration guide on meshtastic.org for details.
Modem Presets
Preset
Range
Швидкість
SNR Limit
Best For
Short Turbo
~1 km
21.9 kbps
−5 dB
Dense urban with line-of-sight; data-heavy applications
Short Fast
~3 km
10.9 kbps
−7.5 dB
Urban neighborhoods; buildings within a few blocks
Short Slow
~5 km
5.5 kbps
−10 dB
Suburban short-range; moderate building density
Medium Fast
~5 km
5.5 kbps
−10 dB
Suburban areas; moderate building density
Medium Slow
~8 km
1.1 kbps
−12.5 dB
Suburban/rural; moderate range with slower speed
Long Turbo
~10 km
4.4 kbps
−10 dB
Similar range to Long Fast but with 500 kHz bandwidth; faster throughput
Long Fast
~10 km
1.1 kbps
−12.5 dB
General use (default) — balanced range and speed
Long Moderate
~20 km
0.34 kbps
−15 dB
Rural with some terrain; occasional use
Lite Fast
~5 km
5.5 kbps
−10 dB
EU 866 MHz SRD band (125 kHz BW); comparable to Medium Fast
Lite Slow
~10 km
1.1 kbps
−12.5 dB
EU 866 MHz SRD band (125 kHz BW); comparable to Long Fast
Narrow Fast
~5 km
2.7 kbps
−10 dB
EU 868 MHz band (62.5 kHz BW); avoids interference with other devices
Narrow Slow
~10 km
1.1 kbps
−12.5 dB
EU 868 MHz band (62.5 kHz BW); comparable to Long Fast
Long Slow
~30 km
0.18 kbps
−17.5 dB
⚠️ Deprecated — still selectable but may be removed in a future firmware release
Very Long Slow
~40+ km
0.09 kbps
−20 dB
⚠️ Deprecated — still selectable but may be removed in a future firmware release
Choosing a Modem Preset
The modem preset controls the fundamental tradeoff between range and data rate:
Slower presets use more spreading, making signals decodable at weaker signal levels (lower SNR limit). This means longer range but fewer bytes per second.
Faster presets pack more data per transmission but require a stronger signal to decode.
Practical guidance:
Urban mesh (many nodes, short distances): Use Long Fast (default) or Short Fast. Higher speed means less airtime congestion when many nodes share the channel.
Rural/sparse mesh (few nodes, long distances): Use Long Moderate. Range matters more than speed when nodes are far apart.
EU 866/868 MHz regulatory compliance: Use Lite Fast, Lite Slow, Narrow Fast, or Narrow Slow — these are optimized for the EU SRD/868 MHz bands with narrower bandwidths.
Fixed infrastructure links: Use Short Turbo or Long Turbo for dedicated point-to-point links with good antennas and line-of-sight.
Mixed environments: Stick with Long Fast — it’s the community default and ensures compatibility with others in your area.
⚠️ Important: All nodes on the same channel must use the same modem preset. Nodes with mismatched presets cannot communicate even if they share the same frequency and encryption key.
💡 Tip: The range estimates above assume flat terrain and modest antennas. Elevation advantage (hilltop, rooftop) dramatically increases effective range. A well-placed Router with Long Fast can often outperform a ground-level node with Long Slow.
Налаштування дисплею
Setting
Опис
Screen Timeout
Time before display sleeps
Одиниці виміру
Metric or Imperial
Тип OLED
Auto, SSD1306, SH1106, SH1107
Compass Orientation
Rotation offset for compass display (0°, 90°, 180°, 270°)
Compass North
⚠️ Deprecated — replaced by Compass Orientation; still visible in older firmware
Position Config
Setting
Опис
GPS Enabled
Enable/disable GPS
GPS Update Interval
How often to acquire GPS fix
Position Broadcast (s)
How often to share position
Інтелектуальне передавання позиції
Enable movement-based broadcasting
Фіксована позиція
Use a manually set position
Налаштування живлення
Setting
Опис
Power Saving
Enable low-power sleep mode
Shutdown After (s)
Auto-shutdown idle timer
ADC Multiplier
Battery voltage calibration factor
Wait Bluetooth (s)
Time to wait for BLE connection at boot
Mesh SDS Timeout (s)
Super-deep-sleep timeout
Налаштування мережі
Setting
Опис
WiFi Enabled
Enable WiFi radio (ESP32 devices)
WiFi SSID
Network name to connect to
WiFi PSK
Network password
NTP-сервер
Time synchronization server
Syslog Server
Remote logging server
Налаштування Bluetooth
Setting
Опис
Bluetooth Enabled
Enable/disable BLE radio
Pairing Mode
Fixed PIN, Random PIN, or No PIN
Фіксований PIN
PIN code for pairing (default: 123456)
Налаштування безпеки
Setting
Опис
Відкритий ключ
Your node’s public key (read-only)
Ключ адміністратора
Key for remote administration
Приватний ключ
Your node’s private key (handle securely)
Admin Channel Enabled
⚠️ Removed — now configured automatically when an admin key is set
Debug Log
Output live debug logging over serial/bluetooth
Serial Enabled
Enable serial console access (moved from Device Config)
Керований режим
Restrict non-admin channel changes
Settings use standard preference controls — dropdowns, toggles, and sliders:
